High-Gloss Interior & Exterior Timber Varnish

KEY BENEFITS

• Ultra-long-life alkyd varnish
• UV resistant
• Water resistant
• Mildew resistant
• Hard-wearing gloss finish
• Interior and exterior use

WHERE TO USE

• Garden furniture
• Window frames
• Shutters and balustrades
• Doors and pergolas
• Fascias and timber gates
• Interior and exterior timber surfaces
• And many more applications

HOW TO USE

• Ensure timber is clean, dry and free from dust, grease and contamination
• Sand new timber using 120–180 grit sandpaper and remove all dust
• Remove old coatings using Nova 08 Novastrip where required
• Stir thoroughly before and during use
• Thin the first coat with up to 20% Mineral Turpentine to improve penetration into timber
• Apply evenly following the timber grain direction
• Apply subsequent coats undiluted using a quality brush or spray equipment
• Allow a minimum of 8 hours between coats
• Lightly sand between coats using 180–220 grit sandpaper
• Remove all sanding dust before recoating
• Allow 16–24 hours drying between coats for optimum gloss development
• Apply a minimum of 2–3 coats depending on timber exposure and porosity
• For spray application, thin with up to 20% Mineral Turpentine where required
• Avoid excessive film build

Critical: Do not apply to damp timber, during rain or high humidity, or to timber intended for permanent water immersion. Not suitable for high-traffic decking applications. Nova 16 must not be applied over Nova 15 Timberseal Penetrating Oil.

Tip: For maximum durability on exterior timber, apply three full coats and pay particular attention to end grain and exposed timber edges.

WHY CHOOSE

• Long-lasting timber protection
• Excellent weather resistance
• Helps protect against moisture and mildew
• Enhances natural timber beauty
• Recommended by the Merensky Foundation

KEY SPECIFICATIONS

• Alkyd timber varnish
• High-gloss finish
• Interior and exterior use
• UV and weather resistant
• Mildew resistant
• Mineral Turpentine clean-up
• Available in multiple pack sizes

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N16NAT | N16IMB | N16KIA | N16SAP | N16MAH | N16MER | N16DOA

The post Nova 16 Novaglow Varnish appeared first on Genkem.

Marine & Exterior Timber Sealer

KEY BENEFITS

• Penetrating timber protection
• UV resistant
• Water repellent
• Anti-fungal protection
• Enhances natural timber appearance
• Will not readily crack or peel

WHERE TO USE

• Exterior doors
• Window frames
• Timber furniture
• Gates and fascias
• Timber cladding
• Garden furniture
• And many more applications

HOW TO USE

• Ensure timber is clean, dry and free from wax, grease and contamination
• Sand new timber using 140–180 grit sandpaper and remove all dust
• Stir thoroughly before and during use
• Apply using a quality bristle brush following the timber grain direction
• Work product thoroughly into end grain, joints and exposed timber edges

For Porous or Weathered Timber:
• Thin the first coat with up to 10–15% Genkem Mineral Turpentine to improve penetration
• Allow 4–8 hours drying depending on conditions

Subsequent Coats:
• Apply a minimum of 2–3 coats
• Allow at least 8–16 hours between coats
• For best results allow overnight drying between coats
• Lightly sand between coats using 220 grit sandpaper

Critical: Not suitable for continuous water immersion, high-traffic decking, below-waterline marine applications or damp timber. Do not apply during rain or in excessively humid conditions.

Tip: Pre-treat exterior timber with Nova 30 Timber Treatment & Preserver before sealing for enhanced long-term timber protection.

WHY CHOOSE

• Designed specifically for exterior timber protection
• Excellent resistance to weathering and UV exposure
• Flexible finish resists cracking and peeling
• Enhances natural timber grain and colour
• Suitable for both interior and exterior timber surfaces

KEY SPECIFICATIONS

• Resin-based timber sealer
• Available in Low Sheen and High Sheen finishes
• Coverage: 8–10m²/L per coat
• Touch dry: 2–4 hours
• Recoat time: 16 hours
• Full cure: 24–48 hours
• Shelf life: 12–24 months

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N14GLO | N14MAT

The post Nova 14 Novaseal Marine Sealer appeared first on Genkem.

Penetrating Timber Protection Oil

KEY BENEFITS

• Penetrating oil system
• UV resistant
• Water resistant
• Nourishes timber
• Matt natural finish
• Will not readily crack or peel

WHERE TO USE

• Pergolas
• Timber gates
• Garage doors
• Timber fascias and fences
• Exterior timber cladding
• Window frames and timber furniture
• And many more applications

HOW TO USE

• Ensure timber is clean, dry and free from wax, grease and contamination
• Remove old coatings using Nova 08 Novastrip where required
• Sand timber smooth and remove all dust before coating
• Stir thoroughly before use
• Product is supplied ready to use and should not normally be diluted
• Apply a generous coat using a clean brush
• Work thoroughly into the timber, end grain and exposed edges
• Allow approximately 24 hours drying between coats
• Apply a second coat where required

Hardwood Application:
• Dense hardwoods such as Balau, Teak, Saligna, Meranti, IPE and Massaranduba may require additional coats
• For difficult hardwoods, an initial 50/50 blend of Nova 15 and Mineral Turpentine may be used to improve penetration

Critical: Do not apply to damp timber, during rain, in high humidity conditions or to timber intended for permanent water immersion. Not suitable for high-traffic decking applications.

Tip: Pre-treat timber with Nova 30 Timber Treatment & Preserver before sealing for improved long-term timber protection and termite resistance.

WHY CHOOSE

• Deep penetrating timber nourishment and protection
• Excellent exterior weather resistance
• Helps reduce moisture penetration and timber drying
• Ideal for difficult timber profiles and hardwoods
• Natural matt finish enhances timber grain and character

KEY SPECIFICATIONS

• Oil-enriched wax-based penetrating sealer
• Natural matt finish
• Coverage: 8–10m²/L per coat
• Recoat time: 24 hours
• Full cure: ±7 days
• Available in Natural, Teak and Mahogany variants
• Shelf life: 12–24 months

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N15MAH | N15NAT | N15TEA

The post Nova 15 Timberseal Penetrating Oil appeared first on Genkem.

Velvet Finish Wooden Floor Sealer

KEY BENEFITS

• Velvet finish
• Hard-wearing protection
• No polishing required
• Non-slip finish
• Easy maintenance
• Preserves natural timber appearance

WHERE TO USE

• Hardwood floors
• Softwood floors
• Parquet flooring
• Strip flooring
• Mosaic flooring
• Interior timber flooring
• And many more applications

HOW TO USE

• Ensure timber moisture content is between 8% and 12%
• Sand surfaces thoroughly and remove all dust before coating
• Do not wash floors before application
• Product is supplied ready to use — do not dilute
• Apply between 10°C and 25°C

Application Tools:
• Quality brush
• Mohair roller
• Floor applicator

First Coat:
• Apply evenly
• Allow drying for 2–4 hours
• Sand using 100 grit sandpaper

Second Coat:
• Remove dust thoroughly
• Apply second coat
• Allow drying for 2–4 hours
• Sand using 220 grit sandpaper

Final Coat:
• Remove dust
• Apply final coat evenly

High Traffic Areas:
• Apply additional light coats where required

Critical: Not suitable for exterior woodwork, decking, damp timber or poorly prepared surfaces. Avoid excessive film build and apply in one direction only.

Tip: Open-grain timbers such as Pine, Oregon Pine and Yellowwood should be pre-treated with Nova Sanding Sealer for best results.

WHY CHOOSE

• Luxurious low-glare velvet finish
• Durable protection for timber floors
• Non-slip performance once cured
• No polishing required
• Suitable for residential and commercial flooring

KEY SPECIFICATIONS

• Polyurethane alkyd-based floor sealer
• Velvet finish (20–35% gloss)
• Coverage: Hardwood ±10m²/L
• Coverage: Softwood ±5m²/L
• Surface dry: 2–4 hours
• Foot traffic: 12 hours
• Full cure: 7 days

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N12CLR

The post Nova 12 NovaFloor Velvet Floor Sealer appeared first on Genkem.

KEY BENEFITS

• Broad-spectrum mould, algae and fungal protection
• Works within the cured coating film
• Helps extend coating lifespan
• Suitable for water-based and solvent-based systems
• Effective in high-humidity environments
• Easy dosage-based additive system

WHERE TO USE

• Interior and exterior paints
• Wood coatings, sealers and primers
• Adhesives and grouts exposed to moisture
• Plasters and textured coatings
• Mortars and filler systems
• Bathrooms, kitchens and humid environments
• And many more applications

HOW TO USE

• Ensure the host coating, adhesive or material system is suitable for use
• Add Nova 31 directly into the product before application
• Mix thoroughly to ensure even distribution throughout the system

Recommended Dosage:
• Paints and coatings: Approximately 5ml per litre
• Adhesives, mortars and fillers: Approximately 5ml per kilogram

• Increase dosage where required in severe contamination or high-risk environments
• Apply the treated product according to the instructions of the host system

Critical: Nova 31 is an additive and must not be applied directly to surfaces. It is designed to be mixed into paints, coatings, adhesives, mortars or fillers before use. It does not replace proper cleaning, mould removal, surface preparation or the correction of moisture ingress problems.

Tip: For best results, first remove existing mould contamination and correct the source of moisture before applying a Nova 31-treated coating system. This helps maximise long-term mould resistance.

WHY CHOOSE

• Provides protection throughout the coating film
• Helps inhibit mould, algae and fungal growth
• Improves coating durability in humid conditions
• Compatible with a wide range of coating and building systems
• Easy to incorporate into existing formulations

KEY SPECIFICATIONS

• Dry-film preservative additive
• Amber liquid appearance
• Specific gravity: ±1.05
• Suitable for water-based and solvent-based systems
• Non-flammable formulation
• Shelf life: 12 months unopened
• Clean-up with White Spirits or Genkem Mineral Turpentine

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N31MKL

The post Nova 31 Mould Killer appeared first on Genkem.

KEY BENEFITS

• Food-grade formulation
• Nourishes and revitalises timber
• Enhances natural timber appearance
• Water-repellent finish
• Easy wipe-on application
• Maintenance recoating without sanding

WHERE TO USE

• Cutting boards
• Butcher blocks
• Wooden kitchen utensils
• Timber serving boards
• Food preparation timber surfaces
• Decorative kitchen timber accessories
• And many more applications

HOW TO USE

• Ensure timber surfaces are clean, dry and free from dust, grease, wax and contamination
• Stir or shake thoroughly before use
• Product is supplied ready to use and must not be diluted
• Apply using a lint-free cloth or soft brush
• Apply a thin even coat following the timber grain direction
• Work the oil thoroughly into end grain, dry timber areas and porous sections
• Allow the oil to penetrate evenly into the timber surface
• Remove excess material using a clean dry cloth where required
• Additional light coats may be applied to dry or porous timber surfaces

Critical: Nova 37 is designed for interior food-contact timber surfaces and is not suitable for exterior weather exposure, continuous water immersion or structural timber protection. Do not apply to damp or contaminated timber surfaces. Excessive application may result in slow drying or surface tackiness.

Tip: Multiple light coats are preferable to one heavy application. Reapply monthly or as required when timber begins to appear dry or loses its natural lustre. Maintenance coats normally do not require sanding.

WHY CHOOSE

• Designed specifically for food-contact timber surfaces
• Helps reduce timber drying and surface cracking
• Easy maintenance and reapplication system
• Non-film-forming natural finish
• Enhances timber grain and colour
• Suitable for repeated maintenance applications

KEY SPECIFICATIONS

• Food-grade timber nourishing oil
• Natural low-sheen finish
• Coverage: 8–10m²/L per coat
• Surface dry: 1–2 hours
• Light handling: 2–4 hours
• Full cure: 4–6 hours
• Warm soapy water clean-up

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N37NBO

The post Nova 37 Food-Safe Wood Oil appeared first on Genkem.

KEY BENEFITS

• Clear polymer polish system
• Non-slip dry-bright finish
• Restores floor shine
• Easy buffing properties
• Water-based formulation
• Easy maintenance system

WHERE TO USE

• Slate floors
• Quarry tiles
• Sealed brick flooring
• Sealed slasto surfaces
• Vinyl floor tiles and sheeting
• Previously sealed decorative floors
• And many more applications

HOW TO USE

• Sweep thoroughly and remove all loose dirt and dust
• Ensure surfaces are clean, dry and free from contamination
• Shake thoroughly before use

Dilution Required:

• Dilute 25ml Nova 13 with 5 litres of clean water
• Mix thoroughly before application

Application:

• Apply using a squeegee or Nova applicator
• Apply a thin, even coat across the floor surface
• Do not rub excessively during application
• Allow approximately 30 minutes drying between coats
• Apply a second coat and allow to dry completely

Finishing:

• Once dry, buff by hand using a soft cloth or use a polishing machine to achieve the desired shine

Maintenance:

• Sweep regularly
• Damp mop where required
• Buff periodically to maintain shine
• Reapply approximately every 2–3 months as required

Critical: Nova 13 is designed for sealed interior hard surface floors only. It is not suitable for unsealed porous surfaces, damp floors or areas exposed to continuous wet conditions. Product must be diluted before use.

Tip: For new slate and quarry tile floors, first seal the surface with Nova 03 Slate ‘n Quarry Tile Dressing before applying Nova 13 to maximise shine and long-term appearance.

WHY CHOOSE

• Restores shine to dull sealed floors
• Non-slip dry-bright finish
• Easy to apply and maintain
• Compatible with Nova 03 sealed floor systems
• Suitable for vinyl floor maintenance
• Water-based and easy to clean up

KEY SPECIFICATIONS

• Water-based polymer floor polish
• Clear lustre finish
• Surface dry: ±30 minutes
• Recoat time: 30 minutes–1 hour
• Full dry: ±1 hour
• Non-flammable formulation
• Clean-up with warm soapy water

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N13DEE

The post Nova 13 Deepshine Floor Polish appeared first on Genkem.

KEY BENEFITS

• Eradicates wood borer, termites, fungi and mould
• Helps protect against re-infestation
• Deep-penetrating solvent-based formulation
• Does not discolour timber
• Ready-to-use with no dilution required
• Compatible with Nova timber finishes once dry

WHERE TO USE

• Interior timber surfaces
• Furniture and antiques
• Doors and window frames
• Interior ceilings and exposed beams
• Timber flooring prior to finishing
• Kitchen cabinets and timber joinery
• And many more applications

HOW TO USE

• Apply only to clean, dry, bare timber surfaces
• Remove all existing paint, varnish, wax or oil coatings before treatment
• Sand timber where required and remove all dust
• Stir before use and do not dilute
• Apply generously using a brush, spray, roller, dip method or suitable hand spray bottle
• Ensure complete saturation and penetration into the timber fibres
• For active infestations, spray directly into borer holes, cracks, joints, crevices and other difficult-to-reach areas
• Do not allow excessive pooling on the surface

Application Guide:
• Timber less than 5mm thickness: Apply 2 coats allowing approximately 30 minutes between coats
• Timber greater than 5mm thickness: Apply 3 coats allowing approximately 30 minutes between coats
• Floors and ceilings: Apply 2–3 coats at the recommended spread rate

• Allow the product to absorb fully and dry before overcoating with a compatible Nova timber finish

Critical: Nova 30 is a timber disinfectant and pre-treatment, not a decorative or protective finish. It must be overcoated with a suitable timber sealer, oil or varnish to complete the protection system. Not suitable for permanently wet, submerged or exterior exposed applications without a protective topcoat.

Tip: For timber affected by wood borer or termite activity, inject or spray Nova 30 directly into visible holes, cracks and crevices before treating the entire surface to maximise penetration and effectiveness.

WHY CHOOSE

• Deep penetration into timber fibres
• Eliminates active biological infestation
• Helps prevent future infestation when used as part of a complete system
• Does not affect timber appearance or dimensional stability
• Non-film-forming and compatible with subsequent coating systems

KEY SPECIFICATIONS

• Solvent-based timber disinfectant
• Ready-to-use formulation
• Coverage: ±6m² per litre
• Touch dry: ±30 minutes
• Recoat time: ±30 minutes
• Brush, roller, spray, dip or hand-spray application
• Clean-up with Nova 11 Cleaner & Degreaser

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N30DIS

The post Nova 30 Wood Treatment & Preserver appeared first on Genkem.

KEY BENEFITS

• Heavy-duty stripping performance
• High-viscosity low-run formulation
• Suitable for vertical and horizontal surfaces
• Effective on paint and varnish systems
• Assists in reducing manual scraping effort
• Fast-acting solvent blend

WHERE TO USE

• Paint removal from timber
• Varnish stripping from wood surfaces
• Metal surface stripping
• Concrete coating removal
• Stone surface stripping
• Furniture refurbishment and restoration
• And many more applications

HOW TO USE

• Ensure surfaces are free from loose dirt and excessive dust
• Stir thoroughly before use
• Product is supplied ready for use — do not dilute
• Work in manageable sections of approximately 1–2m² at a time
• Apply a liberal, even coat using a brush
• Allow the product to remain on the surface for approximately 5–10 minutes or until the coating softens, wrinkles or bubbles
• Remove loosened coating using a scraper, stiff brush or suitable stripping tool
• Repeat application where required for stubborn or multiple coating layers

After Stripping:
• Scrub thoroughly using warm soapy water and a stiff bristle brush
• Rinse thoroughly with clean water
• Allow the surface to dry completely before recoating

For Porous Surfaces:
• Timber, concrete and other porous surfaces must be cleaned with Nova 10 Wax Remover after stripping to remove any residual wax contamination before recoating

Critical: Nova 08 contains wax components that may affect adhesion of subsequent coatings if not properly removed. Always clean stripped porous surfaces with Nova 10 Wax Remover and ensure surfaces are clean, dry and free from residue before applying new coatings. Not suitable for vinyl, soft plastics or fibreglass surfaces.

Tip: For heavily built-up coatings, apply a generous coat and cover the treated area with plastic sheeting during the dwell period. This helps slow solvent evaporation and can improve stripping performance. Paint-hardened brushes can also be restored by soaking in undiluted Nova 08 for 2–5 minutes before rinsing thoroughly.

WHY CHOOSE

• Removes multiple coating types with one product
• Clings effectively to vertical surfaces
• Suitable for restoration and refurbishment work
• Reduces sanding and scraping effort
• Ready-to-use with no mixing required
• Also suitable for cleaning paint-hardened brushes and tools

KEY SPECIFICATIONS

• Solvent blend paint and varnish stripper
• High-viscosity liquid formulation
• Dwell time: 5–10 minutes
• Brush application
• Specific gravity: 1.20–1.30
• Shelf life: 12 months unopened
• Clean-up with QAS501

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N08STR

The post Nova 8 NovaStrip Paint Stripper appeared first on Genkem.

KEY BENEFITS

• Deep penetrating liquid wax
• Nourishes and revitalises timber
• UV-stable formulation
• Enhances natural timber colour and grain
• Excellent water repellency
• Smooth satin finish

WHERE TO USE

• Interior furniture
• Exterior furniture under cover
• Decorative timber pieces
• Sealed timber surfaces
• Previously varnished timber
• Wooden cupboards, shelving and joinery
• And many more applications

HOW TO USE

• Ensure surfaces are clean, dry and free from dust, grease and contamination
• Shake thoroughly before use
• Product is supplied ready to use — do not dilute
• Apply using a soft cloth or soft brush
• Apply a thin even coat following the timber grain direction
• Allow the product to penetrate the timber surface
• Buff lightly by hand to achieve the desired satin finish
• Additional light coats may be applied where increased nourishment or sheen enhancement is required
• Allow adequate drying between coats

Critical: Nova 21 is designed as a nourishing and maintenance wax rather than a structural timber protection system. Not suitable for exterior decking, high-traffic flooring, continuous water exposure or damp timber surfaces. Excessive application may result in slow drying or surface tackiness.

Tip: Multiple light applications produce better results than one heavy coat. Reapply periodically as timber dries or loses lustre to maintain appearance and water repellency.

WHY CHOOSE

• Revives tired and weathered timber surfaces
• Maintains previously sealed timber finishes
• Enhances natural timber grain and colour depth
• Fast drying, non-sticky finish
• Minimal wax build-up with correct application

KEY SPECIFICATIONS

• UV-stable liquid wood wax
• Satin / low-sheen finish
• Excellent water repellency
• Surface dry: 20–40 minutes
• Light buffing: 30–60 minutes
• Full cure: 12–24 hours
• Unlimited shelf life under suitable storage conditions

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N21WAXS

The post Nova 21 Novawax Liquid Wax Satin appeared first on Genkem.