Velvet Finish Wooden Floor Sealer

KEY BENEFITS

• Velvet finish
• Hard-wearing protection
• No polishing required
• Non-slip finish
• Easy maintenance
• Preserves natural timber appearance

WHERE TO USE

• Hardwood floors
• Softwood floors
• Parquet flooring
• Strip flooring
• Mosaic flooring
• Interior timber flooring
• And many more applications

HOW TO USE

• Ensure timber moisture content is between 8% and 12%
• Sand surfaces thoroughly and remove all dust before coating
• Do not wash floors before application
• Product is supplied ready to use — do not dilute
• Apply between 10°C and 25°C

Application Tools:
• Quality brush
• Mohair roller
• Floor applicator

First Coat:
• Apply evenly
• Allow drying for 2–4 hours
• Sand using 100 grit sandpaper

Second Coat:
• Remove dust thoroughly
• Apply second coat
• Allow drying for 2–4 hours
• Sand using 220 grit sandpaper

Final Coat:
• Remove dust
• Apply final coat evenly

High Traffic Areas:
• Apply additional light coats where required

Critical: Not suitable for exterior woodwork, decking, damp timber or poorly prepared surfaces. Avoid excessive film build and apply in one direction only.

Tip: Open-grain timbers such as Pine, Oregon Pine and Yellowwood should be pre-treated with Nova Sanding Sealer for best results.

WHY CHOOSE

• Luxurious low-glare velvet finish
• Durable protection for timber floors
• Non-slip performance once cured
• No polishing required
• Suitable for residential and commercial flooring

KEY SPECIFICATIONS

• Polyurethane alkyd-based floor sealer
• Velvet finish (20–35% gloss)
• Coverage: Hardwood ±10m²/L
• Coverage: Softwood ±5m²/L
• Surface dry: 2–4 hours
• Foot traffic: 12 hours
• Full cure: 7 days

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N12CLR

The post Nova 12 NovaFloor Velvet Floor Sealer appeared first on Genkem.

Interior Polyurethane Timber Varnish

KEY BENEFITS

• Polyurethane protection system
• Water resistant
• Alcohol resistant
• Heat resistant
• Stain resistant
• Hard-wearing finish

WHERE TO USE

• Furniture
• Bookcases
• Cupboards
• Bar tops and tables
• Shelves and decorative trim
• Interior timber doors and joinery
• And many more applications

HOW TO USE

• Ensure timber is clean, dry and free from dust, wax, grease and contamination
• Sand new timber using 140–180 grit sandpaper
• Remove old coatings using Nova 08 Novastrip where required
• Remove wax residue using a suitable wax remover
• Clean oily timbers using Mineral Turpentine and fine steel wool if necessary
• Stir thoroughly before and during use

First Coat:
• May be thinned with up to 20% Mineral Turpentine to improve penetration
• Apply using a clean brush or spray equipment
• Apply evenly following the timber grain direction
• Allow 2–4 hours drying before sanding
• Sand lightly using 160–180 grit sandpaper

Second & Third Coats:
• Remove all sanding dust
• Apply subsequent coats undiluted
• Sand lightly between coats using 180–220 grit sandpaper
• Apply a third coat where required

Spray Application:
• Suitable for spray application at approximately 275kPa

Critical: Not suitable for exterior exposure, timber flooring or permanent water immersion. Do not apply to damp timber or during cold and humid conditions. Avoid excessive film build which may cause runs or wrinkling.

Tip: For enhanced timber colour, apply Nova 18 Novadye before varnishing. Do not mix Nova 18 directly into Nova 17.

WHY CHOOSE

• Durable polyurethane timber protection
• Resistant to water, stains, alcohol and heat
• Enhances natural timber grain and appearance
• Available in Gloss, Satin and Velvet finishes
• Ideal for interior furniture and joinery projects

KEY SPECIFICATIONS

• Solvent-based polyurethane varnish
• Available in Gloss, Satin and Velvet finishes
• Coverage: 5–8m²/L per coat
• Recoat time: 2–4 hours
• Light handling: Overnight
• Full cure: 24–48 hours
• Shelf life: 12 months

EASY TO CHOOSE. EASY TO USE. SINCE 1965.

N17GLO | N17MAT | N17VEL

The post Nova 17 Novathane PU Varnish appeared first on Genkem.